Archive for December, 2007
Monday, December 31st, 2007
| Incra Miter 3000 SE |
| An unprecedented 364 positive stops make this Special Edition jig the standout choice for precise, repeatable cuts. The Incra exclusive AngleLOCK indexing system allows you to lock your angles at 1/2°, 1° and 5° increments over a 180° range. Combine this with the GlideLOCK miter bar, which adjusts for zero play and smooth sliding, and you’ll never have to worry about “angle drift” again. Settings are also continuously variable between 1/2° increments. The telescoping fence with direct read ruler stretches out to a lengthy 48″ for easy-read setups and repeatable cuts on long pieces. To top it off, the innovative Flip Shop Stop features two stops that swing out of the way independently and it’s guaranteed to prevent the tips of mitered pieces from wedging behind the stop.
Incra Miter 3000 SE
|
 |
Posted in New Products | No Comments »
Monday, December 31st, 2007
| 6” Fractional Digital Caliper |
| When it comes to measuring stock, fitting precise joints and setting up machines, a digital caliper is one of the handiest tools to have around. This one reads in convenient fractions so you don’t have to memorize decimal equivalents or make conversions in your head. Unlike most fractional calipers, which read in 1/64ths, this one reads in 1/128ths for maximum precision. Best of all, you can switch from fractions to decimals to millimeters with just the push of a button. Ultra-smooth sliding action allows you to dial in your setting quickly, then lock it down with the knurled knob. Measures inside, outside, depth and steps. Includes pre-installed battery, spare battery and padded plastic case.
6” Fractional Digital Caliper
|
 |
Posted in New Products | No Comments »
Sunday, December 30th, 2007
| Chris Pye Special V Stone for V-Tools |
| With four different angles, this signature slipstone will bring a wide range of V-shaped carving tools to a razor edge. The flat surfaces are perfect for outside bevels, while the four edges each have a different angle for inside bevels: 45°, 60°, 85° and 90°. Ultra-fine hard translucent Arkansas oilstone is the stone of choice for Master woodcarver Chris Pye, producing the finest possible finish in an oilstone. Measures 2-1/2″ x 2-1/2″ x 10mm.
Chris Pye Special V Stone for V-Tools
|
 |
Posted in New Products, Woodturning | No Comments »
Sunday, December 30th, 2007
| Chris Pye Detail Slipstone Set for Micro-Gouges and Mini V-Tools |
| Specially developed with input from Master woodcarver Chris Pye, these miniature slipstones will put a razor edge on a wide range of micro-gouges and mini V-tools. The medium India oilstone features four profiled edges ranging from a mild crown to a half-circle (edges #3, #5, #7 and #9). The three ultra-fine hard translucent arkansas oilstones feature the same profiles as the India stone plus bevels for 45° and 60° V-tools, and will bring your edges to the finest possible sharpness. India stone measures 3″ x 3″ x 3mm. Hard translucent Arkansas stones measure 1″ x 2″ x 3mm. Includes foam-lined plastic case.
Chris Pye Detail Slipstone Set for Micro-Gouges and Mini V-Tools
|
 |
Posted in New Products, Woodturning | No Comments »
Sunday, December 30th, 2007
| Digital Height Gauge |
| Enjoy the rewards of precisely fitting joints and perfectly tuned machines! This multi- purpose gauge is accurate to within 0.001″. It can be used to set the exact height of your blade or bit on the table saw, router table and a host of other machines. You can raise the gauge to the desired height and raise the blade to match, or you can set the caliper on the bit and raise it until the display reads the correct height. It’s also an ideal tool for leveling the knives and setting the depth of cut on your jointer. Heavy, solid steel base provides maximum stability. Changes from inches to millimeters and zeroes out with the push of a button.
Digital Height Gauge
|
 |
Posted in New Products | No Comments »
Saturday, December 29th, 2007
| 2-1/2” Deep Throat Pipe Clamp Fixture – Special Offer! |
| Two clamps for $12.98 — a “steel” of a deal! Please note: Limit 12 per customer. Sale price valid while supplies last! Just over 2-1/2″ of reach make these clamp fixtures perfect when you need lightning fast bar-clamp action with the extended reach of a C-clamp. The jaws can be reversed to work as a spreader — ideal for persuading joints apart for repairs. Multiple disc clutch provides effortless adjustment, secure hold and easy release. Compact handle allows ample finger clearance. Heavy-duty cast iron and steel construction. Use with 3/4″ threaded pipe, not to exceed 1-1/16″ OD. (Pipe sold separately) OPTIONAL ACCESSORY : Zinc Plated Pipe Zinc-plated iron pipe eliminates black marks when gluing up woods like Oak. PLUS, it looks great in the shop.
2-1/2” Deep Throat Pipe Clamp Fixture – Special Offer!
|
 |
Posted in New Products | No Comments »
Saturday, December 29th, 2007
| Irwin 6” Quick Grip Clamp 2-Pack |
| Jaw-dropping price on Quick-Grip Clamps — 2 pack for ONLY $8.99! These fast, lightweight clamps are a snap for small projects, and they’re the perfect size for securing work to the benchtop. They have a rugged design, boast up to 150 lbs. of clamping pressure and are 25% smaller than Quick- Change clamps — great for tight spaces. A one-handed Quick-Release trigger allows fast, easy repositioning. Clamps open to 6-3/4″. Act fast! Supplies are limited! Sale price valid while supplies last!
Irwin 6” Quick Grip Clamp 2-Pack
|
 |
Posted in New Products | No Comments »
Saturday, December 29th, 2007
| Dakota Burl Pen Blank |
| Create a beautiful, unique pen with this blank made from crushed sunflower seed hulls that have been impregnated with formulated resins. Easy to turn and finish. Blank measures approximately 5″ long x 3/4″ square.
Dakota Burl Pen Blank
|
 |
Posted in New Products, Pen Turning Blanks | No Comments »
Saturday, December 29th, 2007
| Pen Press/Drilling Jig |
| Drill and assemble your pens perfectly with flush fittings and a smoothly-operating mechanism! This dual-purpose jig takes care of both prep work and assembly. It holds your blank firmly in position for drilling, creating a precise, perfectly centered hole the entire length of the pen. Later, it smoothly presses your parts together without any bowing or misalignment. Notched jaws automatically center the blank for drilling, while two countersunk holes center the parts during assembly. Large clamping wheel provides slow, controlled pressure so you’ll never crack a casing again.
Pen Press/Drilling Jig
|
 |
Posted in New Products, Pen Turning | No Comments »
Friday, December 28th, 2007
| Cocobolo Turning Blanks |
| Highly sought after for its rainbow-hued color, swirling grain, and marvelous luster, Cocobolo continues to be a favorite exotic species among woodworkers. Ornamental turners prize its hardness, density and ability to hold fine detail. These turning blanks are available in an assortment of sizes for bowls, platters, carvings, bottle stoppers, chess pieces, tool handles, table legs, spindles, finials, candlesticks and whatever else your imagination can conjure up!
Cocobolo Turning Blanks
|
 |
Posted in New Products, Woodturning Blanks | No Comments »
Friday, December 28th, 2007
| Router Design/Inlay Kit |
| Brighten up your projects with classic inlays and charming geometric designs. This simple, carefully engineered system allows you to create hundreds of patterns with your plunge router, including lacework, cutouts, intricate floral designs and classic dovetail keys. Best of all, it’s simple to use. The rotating template discs are clearly labeled and the teeth lock precisely into position; just follow the design guide for foolproof results. If you want to create your own design, the pencil guide allows you to draw it out and refine it before “taking the plunge.” The system comes complete with baseplate, bushings and router bits, so it’s ready to use right out of the box.
Router Design/Inlay Kit
|
 |
Posted in New Products | No Comments »
Thursday, December 27th, 2007
| Beadlock Pro Joinery Kit |
| Get incredibly strong, totally concealed joints with just your hand drill and the Beadlock Pro Kit. Beadlock Pro does everything Beadlock Basic does, but adds greater capacity and adjustability, plus the ability to create traditional smooth-sided mortises. Just pop the included paring block into the jig to provide an accurate guide for your chisel. With a 3-1/2″ width capacity, it will easily handle the large joints found in tables, chairs and big casework. Slide the guide block along the rails to place your mortise precisely where you want it. Includes Beadlock Pro Jig, 3/8″ drill bit, 3/8″ stop collar, 3/8″ Beadlock guide block, 3/8″ mortise paring guide block and a molded plastic case with added space for the optional accessory kits. All Accessory Kits include corresponding guide block, mortise paring guide block, HSS drill bit and stop collar.
Beadlock Pro Joinery Kit
|
 |
Posted in New Products | No Comments »
